AUTOR DO BLOG ENG.ARMANDO CAVERO MIRANDA SÃO PAULO BRASIL

"OBRIGADO DEUS PELA VIDA,PELA MINHA FAMILIA,PELO TRABALHO,PELO PÃO DE CADA DIA,PROTEGENOS DO MAL"

"OBRIGADO DEUS PELA VIDA,PELA MINHA FAMILIA,PELO TRABALHO,PELO PÃO DE CADA DIA,PROTEGENOS  DO MAL"

“SE SEUS PROJETOS FOREM PARA UM ANO,SEMEIE O GRÂO.SE FOREM PARA DEZ ANOS,PLANTE UMA ÁRVORE.SE FOREM PARA CEM ANOS,EDUQUE O POVO.”

“Sixty years ago I knew everything; now I know nothing; education is a progressive discovery of our own ignorance. Will Durant”

segunda-feira, 28 de fevereiro de 2011

Estudio de la acoplabilidad de transformadores de potencia


Estudio de la acoplabilidad de transformadores de potencia TITULACIÓN: Ingeniería Técnica Industrial, Electricidad AUTOR: Alejandro González Vergara TUTOR: Ángel Ramos Gómez Mayo de 2009 Universidad Carlos III de Madrid Escuela Politécnica Superior Departamento de Ingeniería Eléctrica PROYECTO FIN DE CARRERA Estudio de la acoplabilidad de transformadores de potencia TITULACIÓN: Ingeniería

TEXTO COMPLETO AQUI:http://www.4shared.com/document/HEOKJzdr/PFC_Alejandro_Gonzalez_Vergara.html

TRANSFORMADOR DE CORRENTE ELETRÔNICO UTILIZANDO BOBINA DE ROGOWSKI E INTERFACE ÓPTICA COM POF PARA APLICAÇÃO EM SISTEMAS DE POTÊNCIA


TRANSFORMADOR DE CORRENTE ELETRÔNICO UTILIZANDO BOBINA DE ROGOWSKI E INTERFACE ÓPTICA COM POF PARA APLICAÇÃO EM SISTEMAS DE POTÊNCIA

Claudionor Fernandes Chaves

Dissertação de Mestrado apresentada ao
Programa de Pós-Graduação em Engenharia
Elétrica, COPPE, da Universidade Federal do
Rio de Janeiro, como parte dos requisitos
necessários à obtenção do título de Mestre em Engenharia Elétrica.
Orientador: Marcelo Martins Werneck
Rio de Janeiro
Setembro de 2008

FULL THESIS HERE: http://www.4shared.com/document/xfKRhofA/2008093003.html





quinta-feira, 24 de fevereiro de 2011

SOCOMEC UPS

Lecture 4 | The Fourier Transforms and its Applications-Stanford University



Lecture by Professor Brad Osgood for the Electrical Engineering course, The Fourier Transforms and its Applications (EE 261). Professor Osgood wraps up the theoretical aspects of the Fourier Series, an application to heat flow.

The Fourier transform is a tool for solving physical problems. In this course the emphasis is on relating the theoretical principles to solving practical engineering and science problems.

sexta-feira, 18 de fevereiro de 2011

Liderazgo e Innovación

José Luis Roces, Vicerrector del ITBA itba.edu.ar, explica cómo el éxito empresarial depende hoy en día de una cultura de la innovación y de personas talentosas que entienden el trabajo en equipo como una circulación de conocimientos y competencias. Desarrolla una visión compleja e híbrida de la innovación cruce entre modelos Bottom-up y Top-down - y del Liderazgo cruce entre cooperación, competencia y protección -


INTERESANTE CONFERENCIA SOBRE LA INNOVACION,DEBEMOS SER HUMILDES Y NO CREER QUE SOMOS DUEÑOS DE LA VERDAD,UN EJEMPLO REAL E PRACTICO ES LA EMPRESA DE GRANDE SUCESO ECONOMICO Y FINANCIERO GOOGLE .

quinta-feira, 17 de fevereiro de 2011

Congresso Brasileiro de Eletrônica de Potência 2011



No post sobre congressos deste ano comentamos sobre o COBEP 2011. Segue a chamada oficial de trabalhos.

CALL FOR PAPERS

The 11th Brazilian Power Electronics Conference (COBEP\'2011) is being organized by the Brazilian Power Electronics Society (SOBRAEP) and by the Universidade Federal de Rio Grande do Norte – UFRN. The congress will take place in Natal, Rio Grande do Norte, from September 11th to 14th 2011. The aim of this conference is to provide a forum for the discussion for Brazilian and Foreign experts in the Power Electronics area, featuring strong participation of industry and academia.

The digest should be submitted to one of the topics listed below:

1. DC/DC converters and DC power supply systems;
2. Inverters for power supply and UPS applications;
3. AC/DC converters and power factor correction;
4. Electric machines, motor drives and motion control;
5. Control theory applied to power electronics systems;
6. Computer-aided modeling, analysis, design and synthesis of power electronics systems;
7. Digital control applications with Microcontrollers,
8. DSP and FPGA;
9. Power quality, harmonics and reactive power compensation, electromagnetic compatibility
10. (EMC) and electromagnetic interference (EMI);
11. Power electronics in generation, transmission and distribution power systems and renewable power systems;
12. Power semiconductor devices, passive components and magnetism;
13. Integration, packaging and modules;
14. Electronics ballast for lighting;
15. Automotive, aerospace, transportation and utility applications of power electronics;
16. Energy storage;
17. Energy conditioning and
18. Education in power electronics.

Important Dates:
Open submission system: 04 –February, 2011
Extended Digest Submission: Dead-Line - March , 24, 2011
Notification of Acceptance: May, 17, 2011
Final Paper Submission: June, 21, 2011

terça-feira, 15 de fevereiro de 2011

GRANDES LIDERES-Entrevista Eike Batista Março/2010 - Parte 5

GRANDES LIDERES-Entrevista Eike Batista Março/2010 - Parte 4

GRANDES LIDERES-Entrevista Eike Batista Março/2010 - Parte 3

GRANDES LIDERES-Entrevista Eike Batista Março/2010 - Parte 2

GRANDES LIDERES-Entrevista Eike Batista Março/2010 - Parte I

O BRASIL NA VISÃO DOS AMERICANOS ( EIKE BATISTA CBS )

sexta-feira, 11 de fevereiro de 2011

Stefan Schuler und Uwe Scheuermann von Semikron Elektronik: Impact of control strategy on power cycling lifetime

Stefan Schuler und Uwe Scheuermann von Semikron Elektronik: Impact of control strategy on power cycling lifetime:http://www.techcast.com/events/pcim2010/mi-paris-03/

VIDEO PCIM EUROPE 2010


ECCE-ENERGY CONVERSION CONGRESS AND EXPO 2010-SR. LENNART JONSSON VICE PRESIDENT CHIEF TECHNOLOGY OFFICER EATON CORPORATION-ENERGY EFFICIENCY PROGRAM

ECCE 2010-SR. PAUL HAMILTON SENIOR VICE PRESIDENT SCHNEIDER ELECTRIC-PART1

ECCE-ENERGY CONVERSION CONGRESS AND EXPO 2010-SR. PAUL HAMILTON SENIOR VCE PRESIDENT SCHNEIDER ELECTRIC-ENERGY EFFICIENCY PROGRAM

ACCELERATING PHOTOVOLTAICS

Winds of Change: Full Documentary

Encuentro con la Ciencia con Modesto Montoya 06-02-11

Design Tools for Power Electronics: Trends and Innovations

Uwe DROFENIK*, Didier COTTET**, Andreas MÜSING* and Johann W. KOLAR*
* Power Electronic Systems Laboratory, ETH Zurich, ETH-Zentrum / ETL H13, CH-8092 Zurich, Switzerland
Phone: +41-1-632-4267, Fax: +41-1-632-1212, E-mail: drofenik@lem.ee.ethz.ch
** ABB Switzerland Ltd, Corporate Research, CH-5405 Baden-Dättwil, Switzerland
Abstract: Numerical simulation is a standard procedure in
the design of power electronic systems. With simulation, one
can test new concepts immediately without the need to order
components and assembling which might be time-consuming
and expensive. If something fails, there is no destruction but
information about too high voltages and/or currents. Critical
operating states just before failure can be exactly
reproduced, and currents, voltages and junction
temperatures can be easily monitored in simulation which
makes it comparably easy to identify problematic designs.
Expensive equipment for measurement, power supply and
load which is essential for testing prototypes is not needed in
a first design stage. Further advantages of simulation are the
ability to easily visualize fields, flows and distributions of
physical properties, and the ability of automated parameter
optimization and/or statistical analysis with Monte Carlo
techniques.
Due to these advantages it would be desirable to replace
designing and testing prototypes by numerical simulations as
far as possible in order to reduce development time, save
development cost and detect reliability problems.
Unfortunately, practical simulation will never fully map reality.
The power electronic system under investigation has to be
simplified in order to be able to handle the model with a
computer. Numerical simulation will always give a result, but
it is up to experience and knowledge of the design engineer
to verify the usefulness and/or accuracy of the result.
In the paper we discuss what can be numerically simulated,
what limits are given to modelling by scaling laws and what
kind of developments we might experience in the future.
Emphasis is on the numerical simulation of converter
systems.
FUL TEXT HERE:
http://www.pes.ee.ethz.ch/uploads/tx_ethpublications/4347884.pdf

segunda-feira, 7 de fevereiro de 2011

Design and Implementation of Paralleled Multi-Inverter Systems with Redundancy and Hot-swap Features






Design and Implementation of Paralleled Multi-Inverter Systems with RRedundancy and Hot-swap Features author (eng):JIA-Wei He INSTITUTE OF ELECTRICAL ENGINEERING COLLEGE OF ENGINEERING NATIONAL CHUNG CHENG UNIVERSITY -2004
This thesis proposes redundancy and hot-swap features for paralleled multi-inverter systems with voltage control and current weighted distribution control (CWDC) strategy. With a CWDC strategy, instantaneous current is fed back and monitored; thus, weighted output current distribution and fast regulation among the inverters can be achieved for linear and nonlinear loads. Additionally, the proposed paralleled system is equipped with the features of redundancy and hot-swap; therefore, system power rating can be expanded readily and it has high maintainability. Simulation results and hardware measurements from a two-inverter system with either equal or different power ratings have demonstrated the feasibility of the proposed control scheme in fast regulation and weighted current distribution. The proposed redundancy and hot-swap features have improved reliability and stability of the paralleled multi-inverter system.
MAIORES INFORMAÇOES:http://ndltd.ncl.edu.tw/cgi-bin/gs32/gsweb.cgi/login?o=dwebmge

http://ndltd.ncl.edu.tw/cgi-bin/gs32/gsweb.cgi/ccd=F84qJ_/webmge?switchlang=en

Carga eletronica regenerativa para testes de fontes de energia eletrica utilizando conversor com capacitor flutuante

AUTOR(ES)
Edson Adriano Vendrusculo
RESUMO
The conventional method for testing power supplies, batteries, uninterruptible power supply (UPS) and other sources of electric power uses resistors as load. This results in wasted heat and increases the equipments production cost.This work presents a Regenerative Electronic Load to substitute those resistors. The basic topology is a capacitive idling Cuk converter. This converter allows to control independently the input current and permits to provide a sinusoidal output current. An appropriate-gate command allows to have some soft-commutation without the use of any auxiliarycircuit. The same converter, with input and output changed, can operate as a Power Supply with Input Power Factor Correction. The characteristics of soft-commutation and high efficiencyare maintained. A simplehigh-efficiencytransformer allows output isolation. AlItheoretical results are experimentally verified
No setor elétrico algumas indústrias que produzem fontes de alimentação, "no-break" e estabilizadores de tensão testam estes equipamentos, utilizando resistores para simulação da carga. Isto acarreta perda de energia elétrica por geração de calor. O resultado é o aumento do custo de produção. Este trabalho apresenta uma Carga Eletrônica Regenerativa que substitui os resistores. A energia drenada do equipamento sob teste é devolvida à rede, e o gasto de energia limita-se às perdas nos componentes da carga eletrônica. A topologia básica é um conversor Cuk com capacitor flutuante. Este conversor permite controlar independentemente as correntes de entrada e saída. A topologia apresenta comutações suaves, do tipo (ZVS), sem a necessidade de circuitos adicionais. O mesmo conversor , mas com as posições de entrada e saída invertidas, pode ser utilizado como Fonte de Tensão Com Alto Fator de Potência. As características de comutação suave e alto rendimento são preservadas. O conversor permite obter isolação em alta frequência. Protótipos, em ambas configurações, comprovam os resultados teóricos .

LINK PARA O TEXTO COMPLETO:http://cutter.unicamp.br/document/?code=vtls000106877

domingo, 6 de fevereiro de 2011

Radiações perigosas



Nova pesquisa mostra correlação entre casos de morte por câncer e localização das antenas de telefonia celular.

Fonte UFMG - Abril - 2010

Tese de doutorado da engenheira Adilza Condessa Dode defendida na UFMG, no final de março, revela que há fortes evidências entre mortes por câncer e localização de antenas de celulares em Belo Horizonte. A pesquisa confirma resultados de estudos realizados na Alemanha e em Israel.

Com base no geoprocessamento da cidade, a pesquisa constatou que mais de 80% das pessoas que morreram de cânceres relacionados à radiação eletromagnética – emitida pelos celulares – moravam a cerca de 500 metros de distância de alguma antena.

A tese é tema da edição do Boletim UFMG que circula na segunda-feira, 12 de abril.

Níveis seguros?
Há níveis seguros de radiação para a saúde humana? “Esse é exatamente o problema: até agora, ninguém sabe quais os limites de uso inócuos à saúde”, explica Adilza Dode, ao destacar que os padrões permitidos no Brasil são os mesmos adotados pela Comissão Internacional de Proteção Contra Radiações Não-Ionizantes (Icnirp), normatizados em legislação federal de maio de 2009. Para a pesquisadora, esses padrões são inadequados. “Eles foram redigidos com o olhar da tecnologia, da eficiência e da redução de custos, e não com base em estudos epidemiológicos”, assegura.

Entre os 22.543 casos de morte por câncer ocorridos em Belo Horizonte de 1996 a 2006, Adilza Dode selecionou 4.924, cujos tipos – próstata, mama, pulmão, rins, fígado, por exemplo – são reconhecidos na literatura científica como relacionados à radiação eletromagnética.

Na fase seguinte do estudo, elaborou metodologia inédita, utilizando o geoprocessamento da cidade, para descobrir a que distância das antenas moravam as 4.924 pessoas que morreram no período. “A até 500 metros de distância das antenas, encontrei 81,37% dos casos de óbitos por neoplasias”, conta a pesquisadora, professora do Centro Universitário Izabela Hendrix e da Faculdade de Ciências Médicas de Minas Gerais.

“Não somos contra a telefonia celular, mas queremos que o Brasil adote o princípio da precaução, até que novas descobertas científicas sejam reconhecidas como critério para estabelecer ou modificar padrões de exposição humana à radiação não ionizante”, diz a pesquisadora.

Recomendações
Em um capítulo de sua tese, ela lista uma série de recomendações. Entre elas, a de que o Brasil adote os limites já seguidos por países como a Suíça. Sugere, ainda, que o governo não permita transmissão de sinal de tecnologias sem fio para creches, escolas, casas de repouso, residências e hospitais; crie infraestrutura para medir e monitorar os campos eletromagnéticos provenientes das estações de telecomunicação e desestimule ou proíba o uso de celulares por crianças e pré-adolescentes.

Componente da banca que avaliou a tese de Adilza Dode, o professor Francisco de Assis Ferreira Tejo, do Departamento de Engenharia Elétrica da Universidade Federal de Campina Grande, afirma que a tese desenvolvida por Adilza Dode "deve ser um marco para que a sociedade brasileira e o Ministério Público comecem a se debruçar sobre a questão dos efeitos biológicos dos campos eletromagnéticos".

A tese Mortalidade por neoplasias e telefonia celular em Belo Horizonte, Minas Gerais foi defendida em 26 de março de 2010, junto ao Programa de Doutorado em Saneamento, Meio Ambiente, e Recursos Hídricos (Desa) da Escola e Engenharia da UFMG, e teve como orientadora a professora Mônica Maria Diniz Leão, do Departamento de Engenharia Sanitária e Ambiental, da Escola de Engenharia e co-orientadora a professora Waleska Teixeira Caiaffa, do Departamento de Medicina Preventiva da Faculdade de Medicina.

http://www.smarh.eng.ufmg.br/tese.php


sábado, 5 de fevereiro de 2011

Desenvolvimento de uma Carga Eletrônica c.c. Regenerativa para Ensaio de Bancos de Baterias


Desenvolvimento de uma Carga Eletrônica c.c. Regenerativa para Ensaio de Bancos de Baterias

Douglas Alexandre Fernandes Pedroso Dissertação de Mestrado submetida à Banca Examinadora designada pelo Colegiado do Programa de Pós Graduação em engenharia Elétrica da Escola de Engenharia da Universidade Federal de Minas Gerais, como requisito para obtenção do Título de Mestre em Engenharia Elétrica. Orientador: Prof. Porfírio Cabaleiro Cortizo BELO HORIZONTE-MG MARÇO.
26/03/2010

ABSTRACT
Tests of electronic converters, voltage sources and batteries are commonly accomplished in resistive commuted loads or in no-regenerative electronic loads and all the energy of the tests is wasted. Although there are several solutions of electronic loads available, that they allow several operation modes and dynamic tests, but few of them are regenerative. This work proposes a d.c. regenerative electronic load that makes possible the control of the discharge test process in batteries and regenerates the energy to the a.c. grid. The electronic load can also be applied in tests of the d.c. voltage sources. The proposed load has two converters, making possible reduction of losses in relation to the three converters loads, and works in constant current operation mode, controlling the current drained from the tested device. The d.c. regenerative electronic load prototype proposed has a power of 635W. The electronic load has at the input stage a current fed Push-Pull converter which elevates the voltage and adds electric isolation. A full bridge monophase inverter at the output stage provides a sinusoidal current waveform with high power factor to the a.c. grid. Experiments showed good dynamic answer in the current control provided to a.c. grid and also was possible provide a sinusoidal current waveform even under harmonic polluted voltage sources, due to the employment of a PLL. In the experimental results on the output stage, losses of about 5% of the drained power were obtained. By including the input stage, the losses will increase about 10%. This regenerative load presents two main advantages to the industrial sector. First, it allows energy saving and second the possibility of controlled and dynamic tests.
DISSERTAÇAO COMPLETA NO SIGUENTE ENLACE:http://www.cpdee.ufmg.br/defesas/48M.PDF

quinta-feira, 3 de fevereiro de 2011

Rede de Sensores para Monitoração de Poluição via Satélite

Rede de Sensores para Monitoração de Poluição via Satélite

Entrevista de Renata Gadêlha com o Prof. Eduardo Fontana no Programa "Conexão UFPE" da TV Universitária da UFPE,UNIVERSIDADE FEDERAL PERNAMBUCO, a respeito do desenvolvimento de uma rede de sensores para monitoração via satélite do estado de poluição de isoladores de alta tensão do sistema CHESF
Entrevista realizada em 18/11/2010

quarta-feira, 2 de fevereiro de 2011

Understanding Graphene and Graphene Nanostructures

Understanding Graphene and Graphene Nanostructures

Exploring Magnetism with Ferromagnetic III-V Semiconductors

2010/5/30 Osaka,G-COE Exploring Magnetism with Ferromagnetic III-V Semiconductors , H.Ohno , Tohoku University

Toward applications of diamond in power electronics infrastructure for a low-carbon society

Creating Electronic Devices with New Functions...:Hamaya Laboratory

Creating Electronic Devices with New Functions...:Hamaya Laboratory

EEVblog #139 - Let's Select a DC-DC Boost Converter

EEVblog #139 - Let's Select a DC-DC Boost Converter

Einstein's General Theory of Relativity | Lecture 1

Einstein's General Theory of Relativity | Lecture 1


Lecture 1 of Leonard Susskind's Modern Physics concentrating on General Relativity. Recorded September 22, 2008 at Stanford University.

This Stanford Continuing Studies course is the fourth of a six-quarter sequence of classes exploring the essential theoretical foundations of modern physics. The topics covered in this course focus on classical mechanics. Leonard Susskind is the Felix Bloch Professor of Physics at Stanford University.